Vauxhall Antara (2014 year). Manual — part 5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
73
Instruments and
Controls
Steering wheel controls
controls
Steering wheel adjustment
Controls
73
Warning lights, gauges and indi-
cators
80
Information displays
92
Vehicle messages
100
Trip computer
101
The Infotainment system and a
connected mobile phone can be
Unlock lever, adjust steering wheel,
operated via the controls on the
then engage lever and ensure it is
steering wheel.
fully locked.
Further information is available in the
Do not adjust steering wheel unless
Infotainment system instruction
vehicle is stationary and steering
manual.
wheel lock has been released.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
74
Instruments and controls
Adjustable wiper interval
Horn
Windscreen wiper/washer
Windscreen wiper
To set the wiping interval to a value
Press j.
between 1 and 10 seconds:
& = fast
■ Switch on ignition.
% = slow
■ Push lever down from position §.
$ = timed interval wiping or
■ Wait until wiping frequency reaches
automatic wiping with rain
the desired interval.
sensor
§ = off
■ Set lever to position $.
The interval remains stored until the
For a single wipe when the
next change or until the ignition is
windscreen wiper is off, press the
switched off. Switching the ignition on
lever down.
and moving the lever to $ sets the
Do not use if the windscreen is frozen.
interval to 3.5 seconds.
Switch off in car washes.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
75
In this mode, wiping frequency is also
The wiper operates for one cycle to
Windscreen and headlight
affected by vehicle speed. As vehicle
check the system when the key is
washer
speed increases, wiping will become
turned to ignition switch position
more frequent.
ACC.
To turn wiper off, move lever to
Automatic wiping with rain sensor
position §.
Pull lever. Washer fluid is sprayed
onto the windscreen.
If the lever is held longer, the wiper
$ = automatic wiping with rain
operates for two cycles after the lever
Keep the rain sensor area clean by
sensor
has been released and once more
activating the windscreen washer
after a 3 second delay.
The rain sensor detects the amount of
system.
If the headlights are on, washer fluid
water on the windscreen and
is also sprayed onto the headlights.
automatically regulates the frequency
The headlight washer system can
of the windscreen wiper.
only be operated again after a short
delay. If washer fluid level is low then
this delay is increased.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
76
Instruments and controls
Control indicator G illuminates in the
Move lever to activate the rear
A drop in temperature is indicated
instrument cluster when the washer
window wiper:
immediately and a rise in temperature
fluid level is low.
after a time delay.
Push lever
= wiper on
Pull lever
= wiper off
If outside temperature drops to 3 °C,
Wiper activated lighting
the symbol : illuminates in the
With light switch in the AUTO
To activate rear window washer
Board-Info-Display as a warning for
position, when the windscreen wiper
system, press and hold button on end
icy road conditions. : remains
is operated for 8 cycles or more the
of lever. Washer fluid is sprayed onto
illuminated until outside temperature
exterior lights illuminate
rear window and the wiper wipes a
reaches at least 5 °C.
automatically.
few times when the button is
released.
Do not use if the windscreen is frozen.
Rear window wiper/washer
Switch off in car washes.
Outside temperature
In vehicles with Graphic-Info-Display
or Colour-Info-Display, a message
appears on the display as a warning
for icy road conditions. There is no
message below -5 °C.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
77
Automatic time synchronisation
9 Warning
Board-Info-Display
The road surface may already be
icy even though the display
indicates a few degrees above 0
°C.
Clock
Graphic-Info-Display,
Colour-Info-Display 3 95.
The RDS (Radio Data System) signal
of most VHF transmitters
automatically sets the time, identified
by } in the display.
Some RDS transmitters do not send
a correct time signal. In such cases,
Date and time are shown in the
switch off automatic time
Info-Display.
synchronisation and set the time
Board-Info-Display 3 92.
manually.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
78
Instruments and controls
Deactivate (Clock Sync.Off) or
Graphic-Info-Display, Colour-Info-
To set date and time manually, select
activate (Clock Sync.On) automatic
Display
menu item Time, Date from the
time synchronisation with the arrow
Settings menu. The menu is
buttons on the Infotainment system.
displayed. Select the menu items
required and make the desired
To set date and time manually, select
setting.
the menu item for time and date
setting from the Settings menu and
To correct time with the help of RDS,
make the desired setting. The value
select menu item Synchron. clock
ready for modification is marked with
automatical. from the Time, Date
arrows. Use the arrow buttons to
menu. The box in front of Synchron.
make the required setting. The setting
clock automatical. will be checked.
is saved when the menu item is
Graphic-Info-Display,
exited.
Colour-Info-Display 3 95.
To correct time with the help of RDS,
select the menu item for time
With the navigation system, date and
Power outlets
synchronisation from the Settings
time are set automatically upon
menu and make the desired setting.
The outlet can be used to connect
receipt of a GPS satellite signal. If the
electrical accessories.
Board-Info-Display 3 92.
displayed time does not match local
time, it can be corrected manually or
automatically by receiving an RDS
time signal.
Some RDS transmitters do not send
a correct time signal. In such cases,
switch off automatic time
synchronisation and set the time
manually.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
79
Electrical accessories that are
connected must comply with the
electromagnetic compatibility
requirements laid down in
DIN VDE 40 839.
Caution
Do not connect any current-
delivering accessories, e.g.
electrical charging devices or
batteries.
12 Volt power outlets are located
Pull the cap out to use the power
Do not damage the outlet by using
beneath the cupholder in the front
outlet, and replace the cap when not
unsuitable plugs.
centre console, in the rear centre
in use.
console and on the right-hand side of
Stop-start system 3 125.
Do not exceed the maximum power
the load compartment.
consumption of 120 Watts.
Operational with ignition switch in
positions ACC or ON. Use of power
outlets while the engine is not running
will discharge the battery.
Additionally, the power outlets are
deactivated in the event of low vehicle
battery voltage.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
80
Instruments and controls
To reset, press and hold the trip
Warning lights, gauges
Odometer
odometer button for a few seconds
and indicators
The odometer display is located in the
with the ignition on.
centre of the instrument cluster.
Instrument cluster
Tachometer
In some versions, the needles of the
instruments briefly rotate to the end
position when the ignition is switched
on.
Speedometer
The bottom line displays the recorded
distance in miles.
Displays the engine speed.
Drive in a low engine speed range for
Trip odometer
each gear as much as possible.
The top line displays the recorded
distance since the last reset.
Caution
There are two independent trip
Indicates vehicle speed.
odometers. Press the trip odometer
If the needle is in the red warning
button once to toggle between
zone, the maximum permitted
Trip A and Trip B.
engine speed is exceeded. Engine
at risk.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
81
P
= park position
Fuel gauge
Service display
R
= reverse gear
The engine oil life system lets you
N
= neutral
know when to change the engine oil
D
= drive position (automatic
and filter. Based on driving
mode)
conditions, the interval at which an
1-6 = selected gear in manual mode
engine oil and filter change will be
indicated can vary considerably.
Control indicators
Change engine oil 3 89.
The control indicators described are
Service information 3 197.
not present in all vehicles. The
description applies to all instrument
Transmission display
versions. Depending on the
equipment, the position of the control
indicators may vary.
Displays the fuel level in the tank.
When the ignition is switched on,
Control indicator Y illuminates if the
most control indicators will illuminate
level in the tank is low. Refuel
briefly as a functionality test.
immediately 3 146.
The control indicator colours mean:
Never run the tank dry. Erratic fuel
red
= danger, important reminder
supply can cause catalytic converter
yellow = warning, information, fault
to overheat 3 129.
green = confirmation of activation
Diesel engines: if the tank has been
blue
= confirmation of activation
run dry, bleed the fuel system 3 161.
white
= confirmation of activation
Because of the fuel remaining in the
tank, the top-up quantity may be less
Displays the mode or selected gear
than the specified tank capacity
with automatic transmission.
3 209.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
82
Instruments and controls
Control indicators on the
9 Danger
instrument panel
Risk of fatal injury for a child using
a child restraint system together
with activated front passenger
airbag.
Risk of fatal injury for an adult
person with deactivated front
passenger airbag.
k illuminates red.
Front passenger seat belt reminder
3 42.
* illuminates yellow.
The front passenger airbag is
deactivated 3 49.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
83
Control indicators in the instrument cluster
-------------------------------------------------------------------------------------------------------------------------------------------------------------
84
Instruments and controls
When the engine is running, if seat
Turn signal
9 Warning
belt is not engaged, the control
O illuminates or flashes green.
indicator will flash for 100 seconds
Have the cause of the fault
The relevant control indicator flashes
then illuminate until seat belt is
remedied immediately by a
when the turn signal is switched on
fastened.
workshop.
3 109.
If vehicle speed exceeds 14 mph, the
Rapid flashing: failure of a turn signal
control indicator will flash for
Belt pretensioners, airbag system
bulb or the associated fuse or failure
100 seconds along with a warning
3 41, 3 44.
of a turn signal light on trailer.
chime and remains illuminated until
seat belt is fastened.
Both control indicators flash when the
Charging system
hazard warning flashers are active
Fastening the seat belt 3 41.
3 108.
p illuminates red.
Front passenger seat belt reminder k
Bulb replacement 3 161, Fuses
3 42.
Illuminates when the ignition is
3 167.
switched on and extinguishes shortly
after the engine starts. If it does not
Turn signals 3 109.
Airbag and belt tensioners
illuminate, seek the assistance of a
v illuminates red.
workshop.
Seat belt reminder
When the ignition is switched on, v
Illuminates when the engine is
flashes briefly. If it does not flash,
Seat belt reminder for front
running
stays lit or flashes during driving,
seats
Stop vehicle and switch off engine.
there is a fault in the airbag system.
X for driver's seat illuminates or
Seek the assistance of a workshop.
Battery is not charging. Engine
flashes red.
The airbags and belt pretensioners
cooling may be interrupted. The
may fail to trigger in the event of an
brake servo unit may cease to be
k for front passenger's seat
accident.
effective.
illuminates or flashes red, when the
seat is occupied.
Deployment of the belt pretensioners
or airbags is indicated by continuous
illumination of v.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
85
Interrupt your journey immediately.
Control indicator Z also illuminates if
In some cases, the fault can be
Remove key and check drive belt
there is a fault in the diesel particle
eliminated by switching the engine off
condition and tensioning before
filter 3 128 or with the automatic
and back on again. If
g
illuminates
seeking the assistance of a
transmission 3 133. Seek the
again after restarting the engine, the
workshop.
assistance of a workshop as soon as
vehicle may need a service.
possible.
Have the cause of the fault eliminated
Malfunction indicator light
Ensure the fuel filler cap is screwed in
by a workshop.
completely 3 146.
Z illuminates or flashes yellow.
Brake system
Illuminates when the ignition is
Flashes when the engine is
switched on and extinguishes shortly
running
R illuminates red.
after the engine starts. If it does not
Fault that could lead to catalytic
Illuminates when the ignition is
illuminate, seek the assistance of a
converter damage 3 129. Ease up on
switched on and extinguishes shortly
workshop.
the accelerator until the flashing
after the engine starts. If it does not
Can illuminate briefly when driving;
stops. Seek the assistance of a
illuminate, stop and seek the
this is normal and does not indicate a
workshop immediately.
assistance of a workshop.
system fault.
If it stays lit while the engine is
Service vehicle soon
running, the brakes do not operate as
Illuminates when the engine is
normal, or leaks are found in the
running
g
illuminates yellow.
brake system, do not attempt to drive
Fault in the emission control system.
Illuminates when the engine is
the vehicle. Have the vehicle towed to
The permitted emission limits may be
running to indicate a fault in the
a workshop for inspection and repair.
exceeded. Fuel economy and vehicle
engine or transmission electronics.
driveability may be impaired. Seek
The electronics switch to an
9 Warning
the assistance of a workshop
emergency running programme, fuel
immediately.
consumption may be increased and
Stop. Do not continue your
vehicle handling may be impaired.
journey. Consult a workshop.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
86
Instruments and controls
Illuminates when engine is running if
If the control indicator does not
Electrical parking brake
fluid level for brake hydraulics is too
illuminate when the ignition is
fault
low 3 157.
switched on, stays lit or illuminates
j illuminates yellow.
during driving, there is a fault in the
Brake system 3 137.
ABS. The brake system remains
When the ignition is switched on, j
operational but without ABS
illuminates briefly. If it does not
Electrical parking brake
regulation.
illuminate, seek the assistance of a
m illuminates or flashes red.
workshop.
If control indicator u illuminates
When the engine is started, m
during driving along with brake
Illuminates
system control indicator R, there is a
illuminates briefly. If it does not
Electrical parking brake is operating
serious fault in the brake system.
illuminate, seek the assistance of a
with degraded performance 3 137.
Have the system checked
workshop.
immediately by a workshop.
Illuminates
9 Warning
Antilock brake system 3 137.
Electrical parking brake is applied
3 137.
Have the cause of the fault
Upshift
remedied immediately by a
Flashes
workshop.
[ illuminates green.
Electrical parking brake is not fully
Upshifting is recommended for fuel
applied or released.
Antilock brake system
saving purposes.
Switch on ignition, depress brake
(ABS)
pedal and attempt to reset the system
u illuminates yellow.
All wheel drive
by first releasing and then re-applying
the electrical parking brake.
The system is ready for operation
B illuminates or flashes yellow.
If m remains flashing, do not drive
when the control indicator
Illuminates briefly when the ignition is
extinguishes.
switched on. If it does not illuminate,
and seek the assistance of a
workshop.
seek the assistance of a workshop.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
87
Flashes briefly when the engine
Illuminates to indicate there is a fault
Interference due to external sources
in the system.
of ultrasound. Once the source of
is running
interference is removed, the system
The system is temporarily disabled.
If it flashes or illuminates during
will operate normally.
driving, friction material needs to cool
Flashes continuously when the
down: drive the vehicle without
Have the cause of the fault in the
engine is running
braking as much as possible.
system remedied by a workshop.
System fault. Seek the assistance of
Descent control system 3 140.
Ultrasonic parking assist 3 143.
a workshop immediately.
All wheel drive 3 134.
Power steering
Electronic Stability Control
2 illuminates yellow.
b illuminates or flashes yellow.
Descent control system
When the ignition is switched on, 2
When the engine is started, b
u illuminates yellow and/or green.
illuminates briefly. If it does not
illuminates briefly. If it does not
Both the yellow and green control
illuminate, stays lit or illuminates
illuminate, seek the assistance of a
indicators illuminate briefly when the
during driving, there is a fault in the
workshop.
ignition is switched on.
system. Seek the assistance of a
workshop.
Illuminates
Green
Fault in the system. Continued driving
Power steering 3 123.
Illuminates when system is ready for
is possible. Driving stability, however,
operation.
may deteriorate depending on road
Ultrasonic parking assist
surface conditions.
Flashes during driving when system
is in operation, after pressing the u
r
illuminates yellow.
Have the cause of the fault remedied
button.
Fault in system
by a workshop.
or
Yellow
Fault due to sensors that are dirty or
Flashes to indicate system is not
covered by ice or snow
ready for conditions to operate.
or
-------------------------------------------------------------------------------------------------------------------------------------------------------------
88
Instruments and controls
Flashes
When the engine is started, W
Diesel particle filter
The system is actively engaged.
illuminates briefly. If it does not
% illuminates or flashes yellow.
Engine output may be reduced and
illuminate, seek the assistance of a
the vehicle may be braked
workshop.
The diesel particle filter requires
automatically to a small degree.
cleaning.
Illuminates when the engine is
Electronic Stability Control 3 139.
Continue driving until %
running
extinguishes.
Stop vehicle and switch off engine.
Electronic Stability Control
Illuminates during driving
off
Caution
Control indicator % iluminates,
accompanied by a warning chime,
t illuminates yellow.
Coolant temperature too high.
when the diesel particle filter is full.
When the ignition is switched on, t
Start cleaning process as soon as
illuminates briefly. If it does not
Check coolant level 3 155.
possible.
illuminate, seek the assistance of a
If there is sufficient coolant, seek the
workshop.
Flashes during driving
assistance of a workshop.
Illuminates when ESC has been
Control indicator % flashes when the
switched off manually by pressing
maximum filling level of the filter is
Preheating
button t on the centre console.
reached. Start cleaning process
! illuminates yellow.
immediately to avoid damage to the
Electronic Stability Control 3 139.
engine. A warning chime sounds
Preheating is activated. Only
every 3 minutes until the cleaning
activates when outside temperature
Engine coolant
process is complete.
is low.
temperature
Diesel particle filter 3 128, Stop-start
If it illuminates during driving or if the
system 3 125.
W illuminates red.
engine cannot be started, seek the
assistance of a workshop as soon as
possible.
Starting the engine 3 124.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
89
Illuminates when the ignition is
Tyre pressure monitoring
9 Warning
switched on and extinguishes shortly
system
after the engine starts. If it does not
When the engine is off,
w illuminates or flashes yellow.
illuminate, seek the assistance of a
considerably more force is needed
workshop.
to brake and steer. During an
Illuminates
Illuminates when the engine is
Autostop the brake servo unit will
Tyre pressure loss. Stop immediately
still be operational.
and check tyre pressure.
running
Do not remove key until vehicle is
A corresponding message also
Caution
stationary, otherwise the steering
appears on the Info-Display 3 92.
wheel lock could engage
Flashes
Engine lubrication may be
unexpectedly.
Fault in system or tyre without
interrupted. This may result in
damage to the engine and/or
Check oil level before seeking the
pressure sensor mounted (e.g. spare
locking of the drive wheels.
assistance of a workshop 3 154.
wheel). After approx. one minute the
control indicator illuminates
continuously. A corresponding
1. Depress clutch.
Change engine oil
message also appears on the Info-
2. Select neutral gear, set selector
C illuminates yellow.
Display.
lever to N.
When the engine is started, C
Consult a workshop.
3. Move out of the flow of traffic as
illuminates briefly. If it does not
Tyre pressure monitoring system
quickly as possible without
illuminate, seek the assistance of a
3 178.
impeding other vehicles.
workshop.
4. Switch off ignition.
The engine oil life monitor lets you
Engine oil pressure
know when to change the oil. Control
indicator C illuminates to indicate
I illuminates red.
that engine oil life has been
diminished and the oil needs
changing.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст